Edstrom Studio
The Making
Slowly, and on purpose.
A kettlebell is a simple object, a sphere of iron and a handle, which is why every decision in it shows. What follows is how a drawing made in New York is meant to become something you lift each morning and look at each evening. The first collection is still in the making; this is the path it will take.
Designed in New York City.
01 / Design
Two kinds of looking.
The Doric belongs to the built world. Its finish is an expression of early classical Greek architecture, where masons cut a column’s flutes only after the drums were stacked, so each groove ran unbroken from one stone into the next. The columns of the Parthenon carry twenty flutes. So does the Doric.
The Tor belongs to weather. Its relief began on walks along Lake Tahoe and around Walden Pond, in the moment a gust shears across still water, the surface shivers, and the lake goes quiet again. Low, wandering bands travel the whole body, so the eye keeps moving and never settles on an edge.
The two share a handle. Its diameter, and the stance of the horns, were designed for comfortable use across a broader range of hands, smaller ones included. Made for the hand, though hands vary, and no handle can promise every one the same fit.
Development renders.
02 / Pattern
Drawn so the iron can leave cleanly.
Before there is iron, there is a pattern: a full-size positive of the bell from which the mould is formed, and a core that shapes the hollow within. Every face that meets the mould is drawn with draft, a slight taper of at least two degrees, so the pattern can lift away cleanly and the iron can come out whole.
The Doric’s twenty flutes are set at even eighteen-degree intervals, a rhythm drawn in a circle and then read in light.
03 / Cast
The form in iron.
Each bell is specified in sand-cast ductile iron to the ASTM A536 standard: an iron whose graphite forms in small spheres rather than flakes. On the Tor, body and handle are a single casting.
The specification asks that each qualifying pour earn its trust: its chemistry recorded, tensile specimens pulled, its structure examined under the microscope, and each bell traceable to the heat it came from. Only then are the medallion seats and the base machined, as separate and exacting operations.
04 / Finish
Colour, then light.
The finish is specified in layers. First, a cathodic e-coat, drawn onto the iron by electrical charge to protect it. On the Doric there follows a two-tone, low-sheen polyester powder: a deeper colour across body and handle, and a lighter tone on the raised crests of the flutes alone, so the recesses keep the deeper colour and the fluting is drawn in light. No clear coat is laid over it. It comes in Tahoe Navy, Alabaster, Mesa Sand and Blacktop.
The Tor wears a single colour, Alpine Silver: over the same e-coat, a liquid metallic laid continuous across body and handle, beneath a satin two-component clear, so that the relief, not the paint, does the work.
The precision seats are kept free of colour. Into them are set two medallions, specified in 316L stainless steel and seated flush: the front marked with the weight in kilograms and pounds, the rear with EDSTROM. Final colours will be settled on physical samples, never on a screen.
Development renders. Screen colours are not finish samples.
05 / Inspect
Measured, not assumed.
The first of every weight is to be inspected against its drawing before any others follow. Each bell is to be weighed complete, after its finish has cured, so that the number on the medallion is the number in your hand. Colour and sheen are judged against a physical master; the crests, the medallions and the fit of every seat, by eye and by gauge. A model on a screen can be checked. Only the iron can be tested.
06 / The plinth
A place to set it down.
A bell kept on the floor is a bell you stoop for. The plinth is thoughtfully functional: it holds each weight within easy reach, and it keeps the set in view, as furniture rather than equipment.
It is designed in wood: an oak top over oak-veneered faces, front and rear made equal in grain, colour, sheen and corner, with no fastener showing on either. Each station is engraved with its weight. Each receiver is keyed, so a bell settles one way only, its front medallion facing forward, in line with the medallion set into the plinth’s front face.
The Plinth-5 holds five bells, 8 to 24 kg; the Plinth-3 holds 12, 16 and 20 kg. Both are in development, and each will be physically qualified before release.
Development renders.